One question about the line to change the device type.
This is because I would like to change from your device type DD2, and others you have... to my device DD1 and my wheel type, and other devices I have...
I am trying to change from this line into the "filename.pws" [YOUR settings]:
You can not get the LEDs for that specific cars synced because the car uses different RPM values for each gear in the game which FanaLab doesnt support.
First I want to sincerely thank you! I have owned the Podium DD1 F1 wheel (PS4 version) since August 2020 and until I recently loaded your profiles never knew the wheel could feel this good! It was a game changer for me with GT3's and Iracing.
I did have one question - I have multiplied your DD2 FFB settings to 1.25 and it is a bit too strong for me and wondered if I should adjust down the wheel FFB or the game settings you recommended for the Ferrari. I believe I read that you said to keep game settings unchanged and just adjust down the wheel FFB but wanted to confirm.
Just in time for todays new FanaLab version 1.60.1 of course I have my car profiles for DD2 ready and fully adapted to the new changes, in particular every car profile also supports BME ITM auto-page-switch-feature now.
One note: This version has a bug with Fuel logic where the value is 1L wrong. As my profiles all use this Display Feature to show Fuel level once the value lowered 1L with Prio this issue affects all my profiles. So if you use the profiles out-of-box just remember to add 1L to the shown value (for example Display shows F39 when in game the fuel level reached 39,99L which means effectively you have still 40L available, not 39L).
im new ... is also version x64 or it is only x86 .. inside the zip... could you also lod x86 to my windows x64 system... I have drivers now installed as x64
I've been using the Audi profiles for ACC, and they work really well, thank you for taking the time to create them. Have a question, looks like they were created with a Formula V2 wheel, which I own, but I also like to use an R300 Podium with APM.
Are the profiles specific to a wheel as well as a car?
Hey Marcel, thanks for everything you do, absolutely love your profiles. Quick question, is the NASCAR next gen profile correct? Tried it out and it seemed really really heavy. Thanks again :)
Ehm.. I am not Marcel... Dont know why so many people confuse us two over and over again... :D
I just tried and for me its even on the liighter side, FFB bar not going even close to red. Sounds to me like you did not properly applied the 22Nm Max Force I 20Nm Wheel Force settings maybe?!
I did not changed any in game settings, especially I do NOT use the new Damper of the new Update as imho it feels bad. Dynamic Damper still at 100 with DPR on the wheel at 50. That's more than enough Damping.
Hi Guys. Does anyone know where i can find some fanalab LED settings for a CLS DD for ACC? I already found the FFB settings etc, but no LED settings. Thnx!
Comments
OK, thank you!
Thanks so much Maurice!!!
One question about the line to change the device type.
This is because I would like to change from your device type DD2, and others you have... to my device DD1 and my wheel type, and other devices I have...
I am trying to change from this line into the "filename.pws" [YOUR settings]:
<Device BaseType="8" WheelType="15" SWType="12" PedalType="3" BME="True" />
to my line with my device:
<Device BaseType="7" WheelType="14" SWType="??????" PedalType="3" BME="???????" />
YOUR DEVICE TYPE=8 --> DD2
YOUR WHEEL TYPE=15 (XXX)
YOUR PEDAL TYPE=3 --> CLUBSPORT PEDALS V3
.....
My device DD1 --> DEVICE TYPE=7
My WHEEL TYPE=14 --> fANATEC BMW wheel...
My PEDAL TYPE=3 --> CLUBSPORT PEDALS V3 (we have the same)
....
But, I would like to Know what is the meaning for these 2 values:
SWType="12"
BME="True"
Because If I export the iracing defaults values from fanalabs to a filename.pws....
Into the file I get
SWType="1"
BME="False"
Thanks a lot in advance Maurice an BR
Do NOT change IDs on your own.
Just load the profile, accept the mis-match Info and re-save the profile. This will overwrite the devices automatically.
BTW do you have a regular DD1 or a DD1 PS4?
DD1 PS4
Thanks so much Maurice for your quick response
BR
does anyone have a profile for ACC, mainly driving the McLaren on a CSL DD with the McLaren wheel? Thanks in advance.
Hello,
Anyone to tell me where to find RPM values for P217 on iRacing as they are not in phase anymore with the proposed profiles in OP?
Thank you in advance,
Oli
You can not get the LEDs for that specific cars synced because the car uses different RPM values for each gear in the game which FanaLab doesnt support.
OK thank you. Is there a reference sheet for each gear somewhere?
Maurice,
First I want to sincerely thank you! I have owned the Podium DD1 F1 wheel (PS4 version) since August 2020 and until I recently loaded your profiles never knew the wheel could feel this good! It was a game changer for me with GT3's and Iracing.
I did have one question - I have multiplied your DD2 FFB settings to 1.25 and it is a bit too strong for me and wondered if I should adjust down the wheel FFB or the game settings you recommended for the Ferrari. I believe I read that you said to keep game settings unchanged and just adjust down the wheel FFB but wanted to confirm.
Again - Thanks so much for sharing your profiles!
Just in time for todays new FanaLab version 1.60.1 of course I have my car profiles for DD2 ready and fully adapted to the new changes, in particular every car profile also supports BME ITM auto-page-switch-feature now.
One note: This version has a bug with Fuel logic where the value is 1L wrong. As my profiles all use this Display Feature to show Fuel level once the value lowered 1L with Prio this issue affects all my profiles. So if you use the profiles out-of-box just remember to add 1L to the shown value (for example Display shows F39 when in game the fuel level reached 39,99L which means effectively you have still 40L available, not 39L).
Let me know if this works.
im new ... is also version x64 or it is only x86 .. inside the zip... could you also lod x86 to my windows x64 system... I have drivers now installed as x64
did I understand something wrong???
best regards
They are pws files within zip archives for every System.
Race 07, GTR & GTR 2.
I have these old Titles that I still run from time to time and I am looking for Fanalab profiles to suit them.
Are they compatible or too old now?
Those games are way too old.
Thanks for the Quick reply.
Still enjoyable to play them as I have a 500gb HDD full of mods for them all and enjoy them.
just upgraded from G29 to CSL DD and wanted to get them running with it and if profiles were available it would simplify it.
thanks for the response
I've been using the Audi profiles for ACC, and they work really well, thank you for taking the time to create them. Have a question, looks like they were created with a Formula V2 wheel, which I own, but I also like to use an R300 Podium with APM.
Are the profiles specific to a wheel as well as a car?
Robert
Hey Marcel, thanks for everything you do, absolutely love your profiles. Quick question, is the NASCAR next gen profile correct? Tried it out and it seemed really really heavy. Thanks again :)
Is your F Bar turning red?
With the default profile settings yeah
I was running super late models and had to tune the strength down until the red bar stopped and then was more manageable.
Ehm.. I am not Marcel... Dont know why so many people confuse us two over and over again... :D
I just tried and for me its even on the liighter side, FFB bar not going even close to red. Sounds to me like you did not properly applied the 22Nm Max Force I 20Nm Wheel Force settings maybe?!
New Profile for the M4 GT3 in ACC :)
Super Maurice !
Thank you for your reactivity!
I'll test it right away ;)
Thank you! What IN GAME settings are you running after this new update? Particularly, DAMPER (new?), DYNAMIC DAMPER, and FFB GAIN.
Thank you kindly
I did not changed any in game settings, especially I do NOT use the new Damper of the new Update as imho it feels bad. Dynamic Damper still at 100 with DPR on the wheel at 50. That's more than enough Damping.
Gain still 60.
Great thank you
Thank you .
Hi Guys. Does anyone know where i can find some fanalab LED settings for a CLS DD for ACC? I already found the FFB settings etc, but no LED settings. Thnx!