My fanatec control panel CTD after updated to 4.31
DD1, fw v690
Faulting application name: FanatecControlPanel.exe, version: 188.8.131.52, time stamp: 0x61a0a313
Faulting module name: KERNELBASE.dll, version: 10.0.19041.1348, time stamp: 0x9166324b
Exception code: 0xe0434352
Fault offset: 0x0012b502
Faulting process id: 0x50c
Faulting application start time: 0x01d7e471f12918df
Faulting application path: C:\Program Files\Fanatec\Fanatec Wheel\ui\FanatecControlPanel.exe
Faulting module path: C:\Windows\System32\KERNELBASE.dll
Report Id: 93f592a1-9bc9-4ae6-8ea8-41db6aa93fde
Faulting package full name:
Faulting package-relative application ID:
That's great, thanks to the team for sorting -
New Firmware feels great with my DD1 :)
I tried these new beta drivers out with Forza 5 in the hope it would no longer crash on me. Alas it didn't work....
fanatec dd1 f1 ps5. I just upgraded to 431. and when connecting it back to the ps5. I had to turn the base off and on 4 times because the steering wheel buttons did not respond (I tried before turning off the base to disconnect the steering wheel and reconnect it) I was quite scared. someone else with the same problem?
DRI on the CSL E 1.1 has lost the negative options? Only OFF, 1, 2, 3... I was running -3
CSL E 1.1/F V2/V3 pedals
Is there any news on the problem with the Brake readings when I have my CSL Elite LC pedals connected via USB? It shows 1600 odd. Does v431 fix this? I am still on 429. Thanks.
Because it's a game issue, not a driver issue.
Great, Thank you.
@Maurice Böschen Do you still recommend uninstalling all Fanatec software, Drivers and Fanalab, then reboot PC, then install New Drivers, update Firmwares, and then reinstall appropriate Fanalab?
I am using dd2 And I use Porsche 918rsr rims.
Version 431 driver installed
When I run the software, the window closes like a crash after 2-3 seconds.
I tested it on 2 PCs, but it's the same
I can not update my csl elite LC pedals from 1.9 to 1.10 firmware. I can do the procedure but in the end it is written that i still have the 1.9.
Also the control panel some times shuts down with the known message "No response"
I'm going to update the csl dd firmware, but the pc driver version is 431.
Even though it was tested on 411/429, it is still not updated.
But I can't update it. When trying to do motor firmware, the firmware update program stops and turns off.
On the driver, the wheel is recognized, but no matter how much the wheel is turned, the angle does not change.
Does anyone know a solution to this?
after I updated my CSL DD with the ClubSport Shifter SQ V 1.5 and the R300 with Hub V2 to the 431 drivers, my H-Shifter no longer worked. Even a clean installation of the drivers (old uninstalled - directory deleted) was unsuccessful.
I have also updated all of the drivers for the hardware, as requested.
When I connect my McLaren GT3 V2, the display tells me to calibrate the H-Shifter. When I try that, it doesn't accept any input, the display remains with the request that I should press P and move the shifter into a neutral position.
The request to calibrate the shifter is not displayed on the R300 steering wheel, and neither is it on the WRC steering wheel. The prompt is only displayed on the McLaren GT3 V2. Installing the older 429 drivers did not work either.
If I set the shifter to sequential switching, it works, only the H-shifting does not.
Installing the older 429 drivers and older hardware drivers using the manual function was also unsuccessful.
Can you help me?
Thomas from Hamburg
nachdem ich meine CSL DD mit dem ClubSport Shifter SQ V 1.5 und dem R300 mit Hub V2 auf die Treiber 431 geupdatet hatte, funktionierte mein H-Shifter nicht mehr. Auch eine saubere Installation der Treiber (alte deinstalliert - Verzeichnis gelöscht) brachte keinen Erfolg.
Ich habe auch alle Treiber für die Hardware erneuert, wie aufgefordert.
Wenn ich mein McLaren GT3 V2 anschließe, teilt mir das Display mit, dass ich den H-Shifter kalibrieren soll. Wenn ich das versuche, nimmt er keine Eingabe an, das Dispaly bleibt bei der Aufforderung, dass ich P drücken soll und den Shifter in neutrale Position bringen soll.
Beim R300 Lenkrad wird die Aufforderung der Shifter-Kalibrierung gar nicht angezeigt und beim WRC Lenkrad auch nicht. Nur beim McLaren GT3 V2 wird die Aufforerung angezeigt.
Stelle ich den Shifter auf sequenzielles Schalten funktioniert das, nur das H-Shiften nicht.
Ein installieren der älteren Treiber 429, sowie älterer Hardware-Treiber über die manuelle Funktion, erbrachte auch keinen Erfolg.
Können Sie mir helfen?
Thomas aus Hamburg
Has there never been or do I have an issue with my Clubsport Universal Hub for Xbox getting a FW update? everything else updates but this.
I have an issue that the funky switch is not always responsive in the tuning menu.
The ClubSport Universal Hub v1 never featured an updatable Firmware, no.
Not always registered Funky Switch turn is a known limitation since forever of that product which can not be fixed.
Most likely an EMI issue. Have been fixed for various people (me included) by attaching ferrite cores to the cables.
see also: https://forum.fanatec.com/discussion/comment/70496#Comment_70496
Yes, it is. But it can also be fixed by using Fanatec drivers 346 or so it's been reported by others, so some drivers do work for Forza 5.
Thanks for the help.
The following page also helped me
The new drivers are now working.
Is really a strange problem.
I hope Fanatec is working on it.
Danke für die Hilfe.
Folgende Seite hatte mir auch geholfen
Jetzt funktionieren die neuen Treiber.
Ist wirklich ein komisches Problem.
Ich hoffe, Fanatec arbeitet daran.
If you run the program after installing it, it stops for a while and then ends.
Both fanatec drivers v431 and latest fanalab.
CSL DD - 184.108.40.206 & 220.127.116.11
CSL WRC - 4
431's now recognise the CSP V2's as Clubsport Series so thats a good start
have not tested anything in game yet but just on the way there now...............
I'll just try it on auto 1st and see how it goes
Even though the manual states its updateable? That seems a bit off
Where does the manual say that?
4.4 in the original manual. talks about updating the Firmware through the driver
Chapter 4.4 of the manual is talking about WHEL BASE Firmware Update, not about Firmware Update of the Universal Hub. The Universal Hub v1 never had the ability for the user to update the firmware. That is completely new only for the v2 Hub!
Did you use the new damper setting which cam with ACC 1.8?
Happens every time?
Did it just show a loading icon or an error message?
Did work fine with previous drivers?
You can try with pressing the power button for 10 seconds to start the base, this should initiate a base update.
Did you update it before and it worked?
Is the update not starting or is it failing?
Can you check if the quick release sits well in the base shaft? If it looks like it slipped out a bit you could loosen the clamp, push it in more (gently) and then re-tighten it properly.
Yes I was experimenting with it. With v431 this new setting in ACC is not working properly - it was kind of on/off. Approximately up to 60 it's off and after 65 it is heavy as hell.
After I rolled back to 427 and then to 429, the new acc damper it works better, but i got better results, by leaving it at 0 and using ndp/nin/nfr on the wheel to get the wanted feeling.