Are you working on compatibility of DRS leds on Iracing? With the new Mercedes F1 I need to use virtual wheel because the DRS (enable and activated) leds doesnt work with my Fanatec F1 rim (I activated in Fanalab but that issue isnt activated i think).
Today a new FanaLab version 1.62.3 was released which introduced a very neat new feature in form of the possibility to adjust, save and load a Clutch Bite Point value to the profile so every car has a perfectly fine-tuned Clutch Bite Point for a perfect standing start.
Of course therefore I already took all my profiles and carefully adjusted, fine-tuned and saved the respective Clutch Bite Point for every car in the attached new profiles :)
I downloaded this earlier and loaded your profile for the Porsche 992 (Iracing) and it did not already have a "base" clutch bite point set (it showed 0). Did I do something wrong or did you not have a recommended one for that car?
Yes it is a shame, there are so many in the community that do mods and skins and so on, I am rather surprised no one has jumped on doing these fanalab profiles.
Hi. I downloaded Maurice's F1 2020 profile from earlier in this thread, then imported all of the F1 cars (.pws files) using FanaLab. I got a warning about device mismatch, which I ignored because I read it would be ok once I saved it with my hardware settings (I have a Formula V2.5 rim on DD1). However, at some point during saving my new profile, my rim started reporting as V2 instead of V2.5. Seems like this is what Maurice has, so somehow it transferred to me (?) I've uninstalled completely, tried an older driver, older firmware flash, but it still says V2 instead of V2.5. I uninstalled both FanaLab and all drivers, but when reinstalling the driver only it still reports as V2. Is it possible the wrong firmware was flashed as a result of my importing a file with a device mismatch? How can I get my rim recognized as a Formula V2.5 again?
I've been reading up on using the firmware updater within an older driver. But since the wheel now things it's a V2, it'll only show my V2 firmwares. Can you force flash a V2.5 firmware manually?
I wish I knew exactly what triggered this. Latest firmware, latest FanaLab (before uninstalling it), not sure. I tried resetting as much as I could think of. Any ideas appreciated.
That's normal. Every Formula v2 Wheel is internally the same and therefore is a v2. You can select the correct wheel you have on Main Page with the gray dropdown but the variant wont be saved to the profile so in the profile over view it will still always be a v2.
And btw I also saved everything with a Formula v2.5 ;)
Hey Maurice, love all the profiles, quick q. With the ir18, I'm getting some pretty aggressive oscillations, I've tried to tune it out by turning the natural damper and friction up to not much effect. Any suggestions? Many thanks
Thank you! I never noticed the drop-down. It's now showing the variant in the Main page. I mistakenly thought that the variant was also shown in the Fanatec Control Panel , and because it says V2 there (and not V2.5) I thought something was overwritten in firmware. Thanks again.
Maurice, is there a reason the LED's are disabled on the profile for the iRacing Porsche GT3 992 Cup car? I thought I remembered reading previously they didn't match up with the in game ones or something similar but when I enabled them they seem to match pretty well.
Also, because I use usb connection for CSL Elite Load Cell pedals, I could not change BRF, that makes me sick because I want to use 70%. How can I do it?
Would anyone happen to have a profile for the Nascar Trucks/Xfinity? I have a DD2. I noticed that Maurice had a profile for the Next Gen, but not the Trucks/Xfinity. Should I just use that profile, or ?
I've used the Default iRacing Profile for the Trucks and find it comfortable. The plate tracks probably bump up the strength but other than that was happy with how it felt.
I use Maurice profiles, but I have to lower the nw of the fbb a lot, because the steering wheel begins to move uncontrollably from one side to the other... and I don't have the strength to go straight... how do you do it? (iracing)
New Build has MASSIVE performance issues for me where CPU load for ne reason is 99% and the whole game is lagging, including LEDs which makes it impossible to test for a proper FFB and correct LED values.
Will need to have to wait for a hotfix of the game before I can work on the profiles.
Comments
What the numbers in the iRacing profile names mean and how to use them is all explained in the included in game settings readme Text file.
Yes. Ok.
Thank you
Hi Maurice,
Are you working on compatibility of DRS leds on Iracing? With the new Mercedes F1 I need to use virtual wheel because the DRS (enable and activated) leds doesnt work with my Fanatec F1 rim (I activated in Fanalab but that issue isnt activated i think).
Iracing does not support DRS Telemetry so it's not working in Fanalab as well, nothing I can do...
Today a new FanaLab version 1.62.3 was released which introduced a very neat new feature in form of the possibility to adjust, save and load a Clutch Bite Point value to the profile so every car has a perfectly fine-tuned Clutch Bite Point for a perfect standing start.
Of course therefore I already took all my profiles and carefully adjusted, fine-tuned and saved the respective Clutch Bite Point for every car in the attached new profiles :)
Can't wait to try this out Maurice! Thanks for all you do!!!
Hi Maurice,
I downloaded this earlier and loaded your profile for the Porsche 992 (Iracing) and it did not already have a "base" clutch bite point set (it showed 0). Did I do something wrong or did you not have a recommended one for that car?
You need to have driver 437 with the included firmwares installed.
Hi Maurice
Do you can share your setting for assetto corsa for DD2?
Setting fanalabs and ingame
Br
Fma
Thanks again Maurice
Nope, dont drive AC anymore so dont have profiles.
Never mind
If anyone can share these settingd
Good luck, I think Maurice is about the only one that does these profiles, never seen any others online anywhere
It's too bad because many of us play on AC
Yes it is a shame, there are so many in the community that do mods and skins and so on, I am rather surprised no one has jumped on doing these fanalab profiles.
Hi. I downloaded Maurice's F1 2020 profile from earlier in this thread, then imported all of the F1 cars (.pws files) using FanaLab. I got a warning about device mismatch, which I ignored because I read it would be ok once I saved it with my hardware settings (I have a Formula V2.5 rim on DD1). However, at some point during saving my new profile, my rim started reporting as V2 instead of V2.5. Seems like this is what Maurice has, so somehow it transferred to me (?) I've uninstalled completely, tried an older driver, older firmware flash, but it still says V2 instead of V2.5. I uninstalled both FanaLab and all drivers, but when reinstalling the driver only it still reports as V2. Is it possible the wrong firmware was flashed as a result of my importing a file with a device mismatch? How can I get my rim recognized as a Formula V2.5 again?
I've been reading up on using the firmware updater within an older driver. But since the wheel now things it's a V2, it'll only show my V2 firmwares. Can you force flash a V2.5 firmware manually?
I wish I knew exactly what triggered this. Latest firmware, latest FanaLab (before uninstalling it), not sure. I tried resetting as much as I could think of. Any ideas appreciated.
Thank you.
That's normal. Every Formula v2 Wheel is internally the same and therefore is a v2. You can select the correct wheel you have on Main Page with the gray dropdown but the variant wont be saved to the profile so in the profile over view it will still always be a v2.
And btw I also saved everything with a Formula v2.5 ;)
Hey Maurice, love all the profiles, quick q. With the ir18, I'm getting some pretty aggressive oscillations, I've tried to tune it out by turning the natural damper and friction up to not much effect. Any suggestions? Many thanks
There is absolutely nothing you can do to avoid oscillations on this car. It's just horrible....
Hahahaha, fair enough. Appreciate the response :)
Thank you! I never noticed the drop-down. It's now showing the variant in the Main page. I mistakenly thought that the variant was also shown in the Fanatec Control Panel , and because it says V2 there (and not V2.5) I thought something was overwritten in firmware. Thanks again.
Maurice, is there a reason the LED's are disabled on the profile for the iRacing Porsche GT3 992 Cup car? I thought I remembered reading previously they didn't match up with the in game ones or something similar but when I enabled them they seem to match pretty well.
Cheers for any info
Is there any chance that you have files for RF2 😇
great files btw. loving them!
Hello,
Do you have CSW 2.5 settings?
Also, because I use usb connection for CSL Elite Load Cell pedals, I could not change BRF, that makes me sick because I want to use 70%. How can I do it?
Thanks!
Does any one have Iracing Profiles for the latest Fanalab build for the CSL Elite Formula Rim and Base with the V3 Pedals that there willing to share.
Would anyone happen to have a profile for the Nascar Trucks/Xfinity? I have a DD2. I noticed that Maurice had a profile for the Next Gen, but not the Trucks/Xfinity. Should I just use that profile, or ?
I've used the Default iRacing Profile for the Trucks and find it comfortable. The plate tracks probably bump up the strength but other than that was happy with how it felt.
I use Maurice profiles, but I have to lower the nw of the fbb a lot, because the steering wheel begins to move uncontrollably from one side to the other... and I don't have the strength to go straight... how do you do it? (iracing)
Hello Maurice,
hoping those new cars are on the way :)
love your profiles <3
Unfortunately not anytime very soon, no.
New Build has MASSIVE performance issues for me where CPU load for ne reason is 99% and the whole game is lagging, including LEDs which makes it impossible to test for a proper FFB and correct LED values.
Will need to have to wait for a hotfix of the game before I can work on the profiles.