@David Mullally: Try to start your base without attached Steering Wheel and take a look in the driver menu. If your WQR Firmware is correctly displayed, then it's OK (then attach the steering wheel and check for recognizing of steering wheel). When you still see WQR Firmware 0.0.0.0, even after reflashing with new firmware, then you have to contact the support.
just install the wqr firmware manually again after trying my tipp above (and when still displayed 0.0.0.0). You don't need to download the single wqr firmware 1.1.0.3. Go to Firmware Update Menu, check the box for manual update and click on WQR Update (Dont choose for a file). The Driver on your pc has nothing to do with recognizing of steering wheel and WQR modul. You don't need to reinstall it.
@David Mullally Can you try to booting up with attached steering wheel and then to take a look to the drive menu? If it still shows firmware 1.1.0.3, you win! otherwise you have to attach your wheel after booting up. This was a problem with old wqr firmware from driver 455 but the new wqr firmwares since 456 has fixed this problem. If you don't have another steering wheel to try, I would contact support when your attached steering wheel don't recognize after booting up.
Done a full reboot of dd and went back in with wheel attached. And it’s all good.
Thanks for the help. Looks like starting it without the wheel earlier first did the trick. Maybe it didn’t finish properly yesterday or we put wheel on to soon after wqr update.
Comments
Then it would show 0.0.0.0 for more users - which is not the case.
isint there difference between 0.0.0.0 and when it actually show only 0 ?
i notice that when user actually had 0 then wqr was most likely dead, or it was only DD1/DD2 thing ?
He just said a bad sign without explanation and now I’m panicking about it.
No difference, no.
0.0.0.0 is CSL DD and CS DD, 0 is P DD. Both mean that something is wrong with the WQR.
So what should I do. Is it the base itself
https://bi.fanatec.com/discussion/29724/new-2024-clubsport-dd-12nm-firmware-and-update-issues
it should be by default the 1.1.0.3 by read changelog. but you tell everything works. so that makes me just fonder if its just glitch
Everything works fine .check the ye link I just posted. Others had same issue.
i had similar issue with my DD2, some time ago, after i reinstall firmware everything worked
i posted that problem in Driver 455 section, but it was like last year. so not fully remember anyone all the details
I’ll try that maybe. So remove the 462 from the laptop and reinstall again?
no, it not worked for me like this. i needed install old firmware and then update again. i really not fully remember atm anymore the full steps
it could be because this remove the steering wheel pop up not show.
Maurice and suggestions? Please don’t say contact support this base has already been back for coil whine.
@David Mullally: Try to start your base without attached Steering Wheel and take a look in the driver menu. If your WQR Firmware is correctly displayed, then it's OK (then attach the steering wheel and check for recognizing of steering wheel). When you still see WQR Firmware 0.0.0.0, even after reflashing with new firmware, then you have to contact the support.
I’ll try that thanks. Do I need to
delete and download the link from here again for 462 as well? Also do I try to a manual flash on the wqr?
I was told this is straightforward and look
at the hassle I’m having.
@David Mullally
just install the wqr firmware manually again after trying my tipp above (and when still displayed 0.0.0.0). You don't need to download the single wqr firmware 1.1.0.3. Go to Firmware Update Menu, check the box for manual update and click on WQR Update (Dont choose for a file). The Driver on your pc has nothing to do with recognizing of steering wheel and WQR modul. You don't need to reinstall it.
I’ll have a go later ill
update u. Thanks.
Ok just back on. Iv removed the wheel and then connected and it’s saying 1.1.0.3 now not 0.0.0.0. Will I connect the wheel now or what.
just before I went in it told me this update is available
Ok. Just connected wheel and it’s saying all good.
@David Mullally Can you try to booting up with attached steering wheel and then to take a look to the drive menu? If it still shows firmware 1.1.0.3, you win! otherwise you have to attach your wheel after booting up. This was a problem with old wqr firmware from driver 455 but the new wqr firmwares since 456 has fixed this problem. If you don't have another steering wheel to try, I would contact support when your attached steering wheel don't recognize after booting up.
I have a few time. Happened once again 0.0.0.0 but then went to normal every time after. Gonna try that once more now though.
Done a full reboot of dd and went back in with wheel attached. And it’s all good.
Thanks for the help. Looks like starting it without the wheel earlier first did the trick. Maybe it didn’t finish properly yesterday or we put wheel on to soon after wqr update.
David Mullally Congratulations. With a bit of luck it will work. Otherwise you can downgrade to previous firmware and try again.
So far so good. Didn’t even need to flash manual one. I’ll recheck tomorrow.
And make sure every screws of your QR/QR2 are tightly fastened. If not weird things can happen.