thanks a lot, it works. Where do I see the different options I can switch through?
I have seen that there are 5 options, but what do they refer to?
Is it possible to have the gear indicator show only when the last LED is on? At the moment, the gear indicator is when the first of the last 3 remaining LEDs are lit.
I would like the gear to be displayed later. I hope you have understood me.
there is a recommended setting available and should be shown for rF2 but by default it doesn't mess with settings automatically, you have to set them as default manually by pressing the default button of a profile so it goes green. Then it gets loaded automatically each time you have the game running
Above the save and load buttons are check boxes of what parts of the Profile you want to load. If you only load the LED settings your Tuning Menu will not be affected. If loaded already, just change to your favorite Tuning Menu settings manually or load one of your own prifles when only the Tuning Menu checkbox is checked, then it won't overwrite the already loaded LED settings from Maurice.
After some period of time (30min-1h) Rev leds on wheel base and wheel rim stop working, they get stuck in one position, everything else works fine. Some time after that the speed also stops updating and gets stuck on last displayed number, after that Fanalab crashes (didn't have logging filters on yet). This happened also on 1.47b, 2 wheels (Formula V2, CSL Elite wheel). Mem leak?
On new version, the speed on wheel is displayed in mph in iRacing instead of kph. Settings are set to metric and ingame settings are the same as before (Formula V2)
Fanalab keeps working after LEDs freeze and after speed stops working there is no crash window, error or report. Fanalab just shuts down. Wheel doesn't need to be restarted for things to get back to normal, only Fanalab.
Hello all. Just to confirm as i've been having this happen since day 1. When loading profiles, are we to expect ITM pages to load automatically with the profile? For example, i select and favorite page 3 in ITM. Load profile and DD/Rim screens continue to display default fanatec/legacy screens unless i manually update or select the pages in Fanalab.
Just want to confirm if these screen should auto change over to profile's selection when loaded or if this is normal behavior.
Hi. I can't get the leds of my elite PS4 to work in Assetto Corsa (PC).
It works on Dirt Rally 2.0. I could make it work with some profiles I found here in the forum for Assetto Corsa Competizione.
But the led only work for the pits and they flash when revs are at maximum. I can't activate anything elsa in the led menu and in Game Profile Menu the leds in the RPM are all empty. How can I get them to have color inside?
I installed Fanalab 1.51 and 380 drivers and I am using McLaren GT3 wheel and v3 pedals. It was working fine with old Fanalab 1.12 and 345 drivers. Please check print screen from led menu and then Game profile menu. I cant get color in the RPM circles and that must be the problem.
After the changes you made you saved it to your profile right? Did you try to disable and re enable the REV Leds again? Also, did you disable the native LED support in AC?
It would be nice if we could adjust the Rev LED for each gear individually. Very helpful in iRacing. If the first gear fits, e.g. the sixth gear no longer fits in iRacing. Sorry, my english is bad.
Es wäre schön wenn man die Rev LED für jeden Gang einzeln einstellen könnte. Sehr hilfreich in iRacing. Wenn der erste Gang passt, ist z.B. der sechste Gang nicht mehr passend in iRacing.
I have a CSL Elite with P1 wheel and CSP v3, installed last driver, firmware and fanalab.. but the tuning menu page on the FANALAB (no wheel device detected) and the driver application doesn't work :( It's not compatible? Or is there a way to make it work?
Indeed but as far as I know it only helps with very few cars and at the same time makes the software more complex. That's why it isn't as important as other features which don't add much to the complexity and at the same time are usable in more scenarios. Doesn't mean it won't come at some point.
Try to unintall FanaLab and when installing it again, choose the option to reset settings. This will not delete any of your profiles, they will still be available. But this possibly solves some issues like yours.
Curious Marcel or Maurice... Could you ever see the new 9 flash LED's having an option to disable the flash sequences and only display the custom flash colours as solid..?
For example the ACC GT3 Audi Evo turns all nine LED's blue when reaching the flash threshold however they do not flash/blink..
Comments
Hi Maurice
thanks a lot, it works. Where do I see the different options I can switch through?
I have seen that there are 5 options, but what do they refer to?
Is it possible to have the gear indicator show only when the last LED is on? At the moment, the gear indicator is when the first of the last 3 remaining LEDs are lit.
I would like the gear to be displayed later. I hope you have understood me.
Many thanks dir your Help.
Thomas
Excuse me, but there are still a few questions.
What is the difference between "Rev LED" and "Base Rev LED"? Can I read it somewhere?
The gear is set to "1", but which bar do I have to change, if the gear shall be displayed later?
"Flash" means when the LEDs start flashing or the rev limiter is reached, right?
But how do I only influence the gear display?
Wow these are great. I use a CSW 2.5 though, is there a way to get it to work nicely with that? I noticed they're all DD1.
Depending on your wheel base you'll have two sets of Rev LEDs, at the base (e.g. at the CSL Elite) and the wheel.
These could be controlled independently, as long as you don't have a DD or a CSW base, as these don't have Base LEDs.
there is a recommended setting available and should be shown for rF2 but by default it doesn't mess with settings automatically, you have to set them as default manually by pressing the default button of a profile so it goes green. Then it gets loaded automatically each time you have the game running
Above the save and load buttons are check boxes of what parts of the Profile you want to load. If you only load the LED settings your Tuning Menu will not be affected. If loaded already, just change to your favorite Tuning Menu settings manually or load one of your own prifles when only the Tuning Menu checkbox is checked, then it won't overwrite the already loaded LED settings from Maurice.
Hello, I'm having few issues with new 1.51:
Hardware: ESL Elite PS4 WB, CSL Elite Wheel, Formula V2 Wheel, V3 Pedals, Shifter 1.5
Driver: 380
WB FW:679
SW FW: 37
Did you check if Fanalab crashes after the LEDs stop working or do you need to restart the wheelbase?
The 2nd issue was already reported and gets a fix very soon!
Fanalab keeps working after LEDs freeze and after speed stops working there is no crash window, error or report. Fanalab just shuts down. Wheel doesn't need to be restarted for things to get back to normal, only Fanalab.
Hello all. Just to confirm as i've been having this happen since day 1. When loading profiles, are we to expect ITM pages to load automatically with the profile? For example, i select and favorite page 3 in ITM. Load profile and DD/Rim screens continue to display default fanatec/legacy screens unless i manually update or select the pages in Fanalab.
Just want to confirm if these screen should auto change over to profile's selection when loaded or if this is normal behavior.
Thank you.
No that is no feature of Fanalab. So it's working as intended at the moment.
Thank you. Loving the software so far!
Hi. I can't get the leds of my elite PS4 to work in Assetto Corsa (PC).
It works on Dirt Rally 2.0. I could make it work with some profiles I found here in the forum for Assetto Corsa Competizione.
But the led only work for the pits and they flash when revs are at maximum. I can't activate anything elsa in the led menu and in Game Profile Menu the leds in the RPM are all empty. How can I get them to have color inside?
I installed Fanalab 1.51 and 380 drivers and I am using McLaren GT3 wheel and v3 pedals. It was working fine with old Fanalab 1.12 and 345 drivers. Please check print screen from led menu and then Game profile menu. I cant get color in the RPM circles and that must be the problem.
Regards and thanks for any help.
911GT3 PBME wheel + DD2 + Inv V3.
Hi,
When In iRacing, I cannot get the telemetry screen featuring the TC, ABS and Brake Bias on my wheel to display any data.
Is this not supported in iRacing or am I missing a setting somewhere ?
Fanalab says there no telemetry setup required for iRacing.
Thx
TC and ABS are Not supported.
Brake Bias should work.
What's supported by which game can be found in the included ITM FEATURE PDF File.
After the changes you made you saved it to your profile right? Did you try to disable and re enable the REV Leds again? Also, did you disable the native LED support in AC?
I like the rev flash LED picker, but it would be nice so see an option to not have it flash.
Noted for the future
It would also be good, the option of flashing the flags, yellow type.
FanaLab 1.52 (hotfix) now available for download (also updated first post)
That's already planned, good to know that others like the idea as well.
Any help with my Elite PS4 Leds in Assetto Corsa?....
It would be nice if we could adjust the Rev LED for each gear individually. Very helpful in iRacing. If the first gear fits, e.g. the sixth gear no longer fits in iRacing. Sorry, my english is bad.
Es wäre schön wenn man die Rev LED für jeden Gang einzeln einstellen könnte. Sehr hilfreich in iRacing. Wenn der erste Gang passt, ist z.B. der sechste Gang nicht mehr passend in iRacing.
Another thing on the long and growing list of things to come at some point :)
Hi,
I have a CSL Elite with P1 wheel and CSP v3, installed last driver, firmware and fanalab.. but the tuning menu page on the FANALAB (no wheel device detected) and the driver application doesn't work :( It's not compatible? Or is there a way to make it work?
thanks
The CSL Elite v1 does not support the Tuning Menu (as well as the CSL Elite v1.1 and the CSW v2).
Indeed but as far as I know it only helps with very few cars and at the same time makes the software more complex. That's why it isn't as important as other features which don't add much to the complexity and at the same time are usable in more scenarios. Doesn't mean it won't come at some point.
Try to unintall FanaLab and when installing it again, choose the option to reset settings. This will not delete any of your profiles, they will still be available. But this possibly solves some issues like yours.
Curious Marcel or Maurice... Could you ever see the new 9 flash LED's having an option to disable the flash sequences and only display the custom flash colours as solid..?
For example the ACC GT3 Audi Evo turns all nine LED's blue when reaching the flash threshold however they do not flash/blink..
Ehm yes this was discussed here in the latest posts that it's a feature on the to-do list... ;)