The LEDs on Fanalab don't work properly (Formula V2). When the rev lights turn on after each other with the same gap between them, it often starts from the beginning again (first yellow light) and then back to where it was (third red light for example) and keeps going to the blue lights as it should.
Does the same goes for iRacing? I do have the rev lights coming up on the V2 F1 wheel for the new LMP2 car. But when I drive the McLaren F1 it won't work. Tried set is differently, off and on again, back to default etc. Nothing seems to work.
Same goes for every game. You have to disable native LED settings to not interfere with what you set as % values in Fanalab (which you have to adjust for every car btw)
Quick question regarding the BME on iRacing. Everything seems to be working well except I don't see the flag LEDs light up for wheel lock/wheel slip, etc. Is this info available in the telemetry? Is it implemented?
I am running the latest 373 driver with everything updated and the latest fanalab.
Thank you and I will have a look where I can find that setting. To be honest though, I haven't disabled it before so whi it does work for the LMP2 🤷♂️
I'm relatively new in the Fanatec products, I think I've read all information about how to setup pedal rumble, but I got stuck with the settings.
I'm using PC driver 373 with CSW 2.5 and CSP v3, pedal connected to the wheel base. I've also Fanalab V1.47b running. I play ACC mostly, so my priority is to make this one game to work as intended.
So I've 2 options. If I set BLI to any value, than the brake pedal rumble works on the specific value, but the other rumble features (ex. gas pedal rev limiter rumble, brake pedal suspension rumble) are not working. If I set BLI to off, everything works fine, except the ABS rumble.
Since I've installed the brake performance kit I need some feedback to measure the necessary braking force, so without ABS rumble I've no use of this program. Please help whether it's possible or not.
BLI can't be used together with the telemetry based vibration features of Fanalab as BLI is a simulated effect which would interfere with the telemetry data. You can only use either the fake BLI signal or the telemetry based Fanalab vibration stuff forwarded by the game.
I play F1 2019 and would like to know how I change the "ITM" screen on my DD1 ?
And how do I put the gear display in my steering wheel instead of the speed? I have been in the "LED" tab and in "Telemetry Data List I put the" C "in red but this is still the speed I see when I am in F1 2019?
To change the pages just click on the respective page number checkbox. Or press and hold the Tuning Menu Button and then press Dpad left or right.
Sounds you didn't disabled the native Fanatec LED option properly in F1 and you didn't clicked on the two green bars in the Game Profile overview to enable Telemetry, set UDP Port etc.
Yes, I experienced the same, but when I turned BLI off, and switched ABS vibration on in the Fanalab I don't feel any ABS vibration on the brake pedal. However when I allowed the Anti-Lock Brakes to be displayed on the LED tab, then I can see on the led display when it is activated, so the telemetry data is working.
Moin, hab seit Release die DD 1 und hab heute alle Treiber aktualisiert. Jetzt hab ich bei F1 2020 in jeder Runde kurze Aussetzer und der funky switch ist extrem langsam. Benutze die aktuelle fanalap 1.47B! Hat jemand eine Lösung?
Hey. First please write in English only according to the forums rules as this increases your chances to get an answer because everyone and not just Germans understand you ;)
Second FanaLab has nothing to do with how FFB works and how the Funky Switch is acting. That would be more a driver or firmware issue which should be better reported in the driver feedback thread.
However, I know there is a new driver coming out very soon which addresses funky switch issues, maybe it’s worth to get that one a try when it comes out. In the meantime you can go back to driver 346 and flash back the firmwares which are included there to see if it fixes your issues
Please read the first post. Because of a firmware issue the ITM select ion in the BME is disabled for now and will be activate sometime next year. For now you have to use the button combination to change ITM pages.
I don't want to be impatient, but can I have some response about the ABS telemetry rumble? Do I only have the problem? Is there anything that I can check? Should I give you more information?
I'm not sure if my question has been asked. I have the Fanatec ClubSport Pedals V3. The most recent driver version is 328 is Fanalab compatible with my pedals.
I gave up on Fanalab, I couldn’t get a useful rumble out of the pedals with it. I tried SLIMax Manager Pro today with the official driver and it works flawlessly.
Comments
Still nothing in the telemetry-feed while playing. I've also tried restriced instead of public.
Dunno if it's of any relevance, but I do have SimHub installed, but not running.
The LEDs on Fanalab don't work properly (Formula V2). When the rev lights turn on after each other with the same gap between them, it often starts from the beginning again (first yellow light) and then back to where it was (third red light for example) and keeps going to the blue lights as it should.
That's because you did not disabled the native LED function from the game so they interfere with Fanalab.
Oh, damn you are right, Maurice. Thank you so much for this incredibly fast answer. :) You are king, thank you so much for all the support.
Does the same goes for iRacing? I do have the rev lights coming up on the V2 F1 wheel for the new LMP2 car. But when I drive the McLaren F1 it won't work. Tried set is differently, off and on again, back to default etc. Nothing seems to work.
Same goes for every game. You have to disable native LED settings to not interfere with what you set as % values in Fanalab (which you have to adjust for every car btw)
Hi,
Quick question regarding the BME on iRacing. Everything seems to be working well except I don't see the flag LEDs light up for wheel lock/wheel slip, etc. Is this info available in the telemetry? Is it implemented?
I am running the latest 373 driver with everything updated and the latest fanalab.
Thanks!
Wheel Spin and Lock are greyed out within Fanalab, so not supported by the game.
Thank you and I will have a look where I can find that setting. To be honest though, I haven't disabled it before so whi it does work for the LMP2 🤷♂️
Hi all,
I'm relatively new in the Fanatec products, I think I've read all information about how to setup pedal rumble, but I got stuck with the settings.
I'm using PC driver 373 with CSW 2.5 and CSP v3, pedal connected to the wheel base. I've also Fanalab V1.47b running. I play ACC mostly, so my priority is to make this one game to work as intended.
So I've 2 options. If I set BLI to any value, than the brake pedal rumble works on the specific value, but the other rumble features (ex. gas pedal rev limiter rumble, brake pedal suspension rumble) are not working. If I set BLI to off, everything works fine, except the ABS rumble.
Since I've installed the brake performance kit I need some feedback to measure the necessary braking force, so without ABS rumble I've no use of this program. Please help whether it's possible or not.
Best regards,
Bred
BLI can't be used together with the telemetry based vibration features of Fanalab as BLI is a simulated effect which would interfere with the telemetry data. You can only use either the fake BLI signal or the telemetry based Fanalab vibration stuff forwarded by the game.
Hello,
I play F1 2019 and would like to know how I change the "ITM" screen on my DD1 ?
And how do I put the gear display in my steering wheel instead of the speed? I have been in the "LED" tab and in "Telemetry Data List I put the" C "in red but this is still the speed I see when I am in F1 2019?
François.
ITM can be controlled in the ITM Tab.
To change the pages just click on the respective page number checkbox. Or press and hold the Tuning Menu Button and then press Dpad left or right.
Sounds you didn't disabled the native Fanatec LED option properly in F1 and you didn't clicked on the two green bars in the Game Profile overview to enable Telemetry, set UDP Port etc.
I just saw that "Fatanec LED" must be put off in F1 2019
Yes, I experienced the same, but when I turned BLI off, and switched ABS vibration on in the Fanalab I don't feel any ABS vibration on the brake pedal. However when I allowed the Anti-Lock Brakes to be displayed on the LED tab, then I can see on the led display when it is activated, so the telemetry data is working.
Update: I tested the pedals via USB (it took more than an hour to plug in the USB), but the situation is the same.
Moin, hab seit Release die DD 1 und hab heute alle Treiber aktualisiert. Jetzt hab ich bei F1 2020 in jeder Runde kurze Aussetzer und der funky switch ist extrem langsam. Benutze die aktuelle fanalap 1.47B! Hat jemand eine Lösung?
Hey. First please write in English only according to the forums rules as this increases your chances to get an answer because everyone and not just Germans understand you ;)
Second FanaLab has nothing to do with how FFB works and how the Funky Switch is acting. That would be more a driver or firmware issue which should be better reported in the driver feedback thread.
However, I know there is a new driver coming out very soon which addresses funky switch issues, maybe it’s worth to get that one a try when it comes out. In the meantime you can go back to driver 346 and flash back the firmwares which are included there to see if it fixes your issues
Why I can't change BME ITM? ...Plz Help me..
Fanatec Driver : 373
FanaLab : 1.47B
Please read the first post. Because of a firmware issue the ITM select ion in the BME is disabled for now and will be activate sometime next year. For now you have to use the button combination to change ITM pages.
Hi Maurice,
I don't want to be impatient, but can I have some response about the ABS telemetry rumble? Do I only have the problem? Is there anything that I can check? Should I give you more information?
Thank you in advance!
Best regards,
Gabor
Hello everybody
I've got a question
since i have been using fanalap i don't have the same feeling with my DD2 anymore and it feels like something is grinding.
does it also change the base ?? it is extremely poor performance
normally i had the podium porsche steering wheel ffb 70 now i have to go to 100.
but still have the old version 1-23
I'm not sure if my question has been asked. I have the Fanatec ClubSport Pedals V3. The most recent driver version is 328 is Fanalab compatible with my pedals.
No. You need at least beta driver 373 you can find here in the forum. Also lknked in first post.
Thanks.
Has anyone else noticed that the rumble motor test doesn't work for V3 pedals in latest driver 373?
I have. You mean for the throttle right ?
I have posted about it.
What wheel are you using ?
No problems here ,all fine with rumble test ,my pedals connect with USB not on the Base
At least I know that you are still alive! :)
I gave up on Fanalab, I couldn’t get a useful rumble out of the pedals with it. I tried SLIMax Manager Pro today with the official driver and it works flawlessly.
Oh right. I'm using the pedals connected to the base and not working.
Anyone else have the issue?