Since i can´t find anyone having the same Rig and problem as me, I´ll try my luck here:
I still have the csw 2.5 wheelbase and the formula 2.5 wheel connected to it (QR1 as i cant upgrade on taht WB).
The Wheel has already been repleace by fanatec due to the firmware update loop i had before with the wheel but it still shows as FW0 (which seems to be a known issue since driver 455?!)
The bigger issue for me is that i suddenly loose FFB and i cant shift anymore mid race - randomly - and regain it slowly back after a few seconds, since i still can steer during that i think its the wheel.
I already downgraded to 455, was on 464 before and it doesn´t change, sadly im not sure if this is conencted to the Update Loop error i have with the wheel.
I googled so much and found literally nothing that comes close to my situation so i hope someone can help me here.
Hello, yesterday my fanatec CSL DD QR2 was updated and after the update the steering wheel always turns to the right. Saturation in WRC at 100%. Please help.
ich bin ganz neu im Simracing und ich habe vor ca. 2 Wochen mein Equipment von Fanatec bekommen. CLS DD (8NM) + Clubsport v2.5x + Padel v3. Ich spiele ausschliesslich F1 24, bis jetzt. Ich fahre auf einem Gaming Laptop Acer Nitro 5 (Ryzen 7 5800h + 16 GB RAM + Nvidia Geforce rtx 3070 (8gb).
Ich habe exakt die gleichen Probleme mit dem Schalten, wie sie hier schon angesprochen wurden. Ich habe nach der ersten Installation und den ersten Fahrten gleich ein support Ticket auf gemacht und jetzt nach 2 Wochen ein RMA bekommen. Wenn ich das aber richtig verstehe, handelt es sich um ein bekanntes Firmware Problem? Was würde dann eine Rücksendung bewirken?
Was mir aufgefallen ist. Wenn ich in F1 24 Time Trail fahre und sonst niemand auf der Strecke ist, passieren die Schaltaussetzter fast immer vor den gleichen Kurven der Strecke. Kann es sein, das die Rechnerleistung doch nicht ausreicht und an Stellen der Strecke wo mehr Grafik gefordert ist einfach die Signale nicht schnell genug im Game ankommen? Ich habe massig Videos gesehen. Wenn ich sehe in welcher Geschwindigkeit da runter geschaltet wird. Da kann ich nur von Träumen 😒 Wenn ich die Schaltwippe 3 mal richtig schnell betätige, kommt im Spiel meist nur ein Schaltvorgang dabei raus.
Wäre es möglich, dass obwohl die min. Hardware Voraussetzungen erfüllt sind, die Schaltprobleme durch den Rechner ausgelöst werden?
Hello, yesterday my fanatec CSL DD QR2 was updated and after the update the steering wheel always turns to the right. Saturation in WRC at 100%. Please help.
Kunden haben seit JAHREN Probleme mit den Treibern sowie der Firmware und jedesmal heisst es, Fehler sei bekannt und wird in Zukunft gefixed. 2024 hieß es großmäulig es werde jeden Monat ein Release avisiert. Tja, es ist 2025 und die Probleme bestehen nach wie vor, von monatlichen releases keine Spur.
Ende 2024 wieder eine dieser Behauptungen im Dezember 24 was zu releasen, aber spätestens Anfang dann 25 - versprochen. Nix passiert.
Im März 25 heisst es nun "Ostern", in einer "ersten Schritt" Variante und im Sommer dann der nächste, um im Herbst dann wieder irgendwas ..
Wer soll den Stuss eigentlich noch glauben?
Und bevor hier wieder der Pfosten auf englisch pocht: Lick my salty vanilla balls!
Marcel Pfister and Maurice Boschen I made the update 464 and during the update I had a bug which made an error with the update of my clubsport hub xbox v2 and since I cannot more update it, because it marks to me error firmware file not found, I tried in manual and automatic on several driver of the 455 to the 464 and I do not manage to update it, that displays to me well but with an update which displays the number zero (I put you the captures of screens).
I've tried on several usb ports on my pc and with the original usb cable supplied with the base without a multi-socket and the base is connected directly to the mains without using a multi-socket and each time I get this error telling me that it can't find the corresponding update file.
So I'd like to have the clubsport hub xbox v2 update file, because I know it's possible to have the files separately and go and get them by going through the fanatec update software on my pc to install them manually with the three dots tab that opens the folders on our pc.
Knowing that I've already seen on your forum that there was a file for the QR, but also one for the podium hub and the clubsport DD+ base, I imagine that it's possible to have a file for the clubsport hub xbox v2 that you can give me so that I can do the manipulation?
Marcel Pfister and Maurice Boschen I made the update 464 and during the update I had a bug which made an error with the update of my clubsport hub xbox v2 and since I cannot more update it, because it marks to me error firmware file not found, I tried in manual and automatic on several driver of the 455 to the 464 and I do not manage to update it, that displays to me well but with an update which displays the number zero (I put you the captures of screens).
I've tried on several usb ports on my pc and with the original usb cable supplied with the base without a multi-socket and the base is connected directly to the mains without using a multi-socket and each time I get this error telling me that it can't find the corresponding update file.
So I'd like to have the clubsport hub xbox v2 update file, because I know it's possible to have the files separately and go and get them by going through the fanatec update software on my pc to install them manually with the three dots tab that opens the folders on our pc.
Knowing that I've already seen on your forum that there was a file for the QR, but also one for the podium hub and the clubsport DD+ base, I imagine that it's possible to have a file for the clubsport hub xbox v2 that you can give me so that I can do the manipulation?
On 464, all drivers up to date, can anyone even tell me what this PDD Quick Release is, hardware or software problem, I managed to get an older firmware on eventually 365 I think, fan started spinning constantly, no wheel recognized, but as soon as I update to 464 again, the misery starts, not much to find searching here or on Google. Copy and paste from the hardware thread.
Hoping someone can help, DD1 last night, playing iRacing, done a few laps, came into the pits to change setup, and noticed my wheel was unresponsive.
Then i Noticed the pop up below, from the Fanatec Firmware Updater, my wheelbase and wheel are not recognized by any software, Fanalabs or Fanatec control panel.
Done the power on power off dance multiple times (wheelbase starts, Fanatec message on the LCD and wheel turns), reboot computer etc., can't do a firmware reload or roll back as the base is not found, was on the latest driver since release, no problems at all until this.
Anyone seen this before or possibly has a fix? I didnt initiate any update at all, like i said, i was in game at that moment.
I am the owner of a CSL DD 8nm year 2021 and Formula v2.5x and I recently acquired the QR2 so as to update the connection, initially I had the 464 driver and related firmware, then reading in the various forums I downgraded the firmware with the 355 driver, I was wondering, then do I leave the 355 driver installed or can I switch to the 464 but without updating the firmware? what should be done?
Comments
Solved my own problem sorry
Since i can´t find anyone having the same Rig and problem as me, I´ll try my luck here:
I still have the csw 2.5 wheelbase and the formula 2.5 wheel connected to it (QR1 as i cant upgrade on taht WB).
The Wheel has already been repleace by fanatec due to the firmware update loop i had before with the wheel but it still shows as FW0 (which seems to be a known issue since driver 455?!)
The bigger issue for me is that i suddenly loose FFB and i cant shift anymore mid race - randomly - and regain it slowly back after a few seconds, since i still can steer during that i think its the wheel.
I already downgraded to 455, was on 464 before and it doesn´t change, sadly im not sure if this is conencted to the Update Loop error i have with the wheel.
I googled so much and found literally nothing that comes close to my situation so i hope someone can help me here.
This is a wheel rim firmware issue I think. Disable the vibration motors in the Control Panel and see if it fixes the issue.
Downgrading the driver to 455 isn't enough. You need to downgrade the firmware too.
Like the vibration from the wheel itself?
I tried that as well by falshign the firmware again with 455 but neither did work i even tried manual fw update if i did it right
(Started firmware updater with 455 driver selected manual and just went with teh .\default or did i do sth wrong?)
Since i cant see the right FW i dont know which one im on
Yeah, Vibration on the wheel rim tab. Dunno about the firmware downgrade, never had to do that. But I think the manual covers it.
I just ckecked it and it was already off as the CSW 2.5 doesnt seem to support it
Has the shifting issue with Clubsport DD and Clubsport Formula v2.5 been fixed yet? I am still running 455?
It hasn't. And it's not a shifting issue, but general button failure issue (which the shifters are part of obviously).
Weiß man schon wann die neue Software erscheint?
Weil das Schaltproblem nervt ziemlich
The next two drivers wont fix the shifting issues because the devs still were not able to reproduce the issue at all.
There is no ETA for a fix for that particular issue yet but not before summer it seems.
Hallo zusammen,
ich bin ganz neu im Simracing und ich habe vor ca. 2 Wochen mein Equipment von Fanatec bekommen. CLS DD (8NM) + Clubsport v2.5x + Padel v3. Ich spiele ausschliesslich F1 24, bis jetzt. Ich fahre auf einem Gaming Laptop Acer Nitro 5 (Ryzen 7 5800h + 16 GB RAM + Nvidia Geforce rtx 3070 (8gb).
Ich habe exakt die gleichen Probleme mit dem Schalten, wie sie hier schon angesprochen wurden. Ich habe nach der ersten Installation und den ersten Fahrten gleich ein support Ticket auf gemacht und jetzt nach 2 Wochen ein RMA bekommen. Wenn ich das aber richtig verstehe, handelt es sich um ein bekanntes Firmware Problem? Was würde dann eine Rücksendung bewirken?
Was mir aufgefallen ist. Wenn ich in F1 24 Time Trail fahre und sonst niemand auf der Strecke ist, passieren die Schaltaussetzter fast immer vor den gleichen Kurven der Strecke. Kann es sein, das die Rechnerleistung doch nicht ausreicht und an Stellen der Strecke wo mehr Grafik gefordert ist einfach die Signale nicht schnell genug im Game ankommen? Ich habe massig Videos gesehen. Wenn ich sehe in welcher Geschwindigkeit da runter geschaltet wird. Da kann ich nur von Träumen 😒 Wenn ich die Schaltwippe 3 mal richtig schnell betätige, kommt im Spiel meist nur ein Schaltvorgang dabei raus.
Wäre es möglich, dass obwohl die min. Hardware Voraussetzungen erfüllt sind, die Schaltprobleme durch den Rechner ausgelöst werden?
Grüße Marcus
Hello, yesterday my fanatec CSL DD QR2 was updated and after the update the steering wheel always turns to the right. Saturation in WRC at 100%. Please help.
You need to backdate the firmware to 454 or 455 either should be fine then update from there. This worked for me.
Es ist definitiv ein Firmware Problem, ein RMA wird nichts bewirken. Der Support ist unfähig.
Lade den Treiber in der Version 455 herunter, und downgrade dann die Firmware auf 0.3.5.0, dann ist das Problem weg.
Kunden haben seit JAHREN Probleme mit den Treibern sowie der Firmware und jedesmal heisst es, Fehler sei bekannt und wird in Zukunft gefixed. 2024 hieß es großmäulig es werde jeden Monat ein Release avisiert. Tja, es ist 2025 und die Probleme bestehen nach wie vor, von monatlichen releases keine Spur.
Ende 2024 wieder eine dieser Behauptungen im Dezember 24 was zu releasen, aber spätestens Anfang dann 25 - versprochen. Nix passiert.
Im März 25 heisst es nun "Ostern", in einer "ersten Schritt" Variante und im Sommer dann der nächste, um im Herbst dann wieder irgendwas ..
Wer soll den Stuss eigentlich noch glauben?
Und bevor hier wieder der Pfosten auf englisch pocht: Lick my salty vanilla balls!
Kann mir einer erklären,wie ich die Firmware zurück downgraden kann?
Mfg Jens
Forum rules are to use english…
Even Fanatec doesn't care anymore, so why would anybody else.
Maurice. thanks for update. Hopefully a fix soon.
Thanks for info
Hey Maurice just downloaded 464 on csl dd my wrc wheel firmware is 0
My mclaren v2 is 47 and working fine...
I've uninstalled and did clean reset, delete, install... can u send me the wrc wheel firmware so I can try manually install wheel firmware pls
Hello @Marcel Pfister and @Maurice Boschen ,
Marcel Pfister and Maurice Boschen I made the update 464 and during the update I had a bug which made an error with the update of my clubsport hub xbox v2 and since I cannot more update it, because it marks to me error firmware file not found, I tried in manual and automatic on several driver of the 455 to the 464 and I do not manage to update it, that displays to me well but with an update which displays the number zero (I put you the captures of screens).
I've tried on several usb ports on my pc and with the original usb cable supplied with the base without a multi-socket and the base is connected directly to the mains without using a multi-socket and each time I get this error telling me that it can't find the corresponding update file.
So I'd like to have the clubsport hub xbox v2 update file, because I know it's possible to have the files separately and go and get them by going through the fanatec update software on my pc to install them manually with the three dots tab that opens the folders on our pc.
Knowing that I've already seen on your forum that there was a file for the QR, but also one for the podium hub and the clubsport DD+ base, I imagine that it's possible to have a file for the clubsport hub xbox v2 that you can give me so that I can do the manipulation?
Thank you
Hello @Marcel Pfister and @Maurice Boschen ,
Marcel Pfister and Maurice Boschen I made the update 464 and during the update I had a bug which made an error with the update of my clubsport hub xbox v2 and since I cannot more update it, because it marks to me error firmware file not found, I tried in manual and automatic on several driver of the 455 to the 464 and I do not manage to update it, that displays to me well but with an update which displays the number zero (I put you the captures of screens).
I've tried on several usb ports on my pc and with the original usb cable supplied with the base without a multi-socket and the base is connected directly to the mains without using a multi-socket and each time I get this error telling me that it can't find the corresponding update file.
So I'd like to have the clubsport hub xbox v2 update file, because I know it's possible to have the files separately and go and get them by going through the fanatec update software on my pc to install them manually with the three dots tab that opens the folders on our pc.
Knowing that I've already seen on your forum that there was a file for the QR, but also one for the podium hub and the clubsport DD+ base, I imagine that it's possible to have a file for the clubsport hub xbox v2 that you can give me so that I can do the manipulation?
Thank you
On 464, all drivers up to date, can anyone even tell me what this PDD Quick Release is, hardware or software problem, I managed to get an older firmware on eventually 365 I think, fan started spinning constantly, no wheel recognized, but as soon as I update to 464 again, the misery starts, not much to find searching here or on Google. Copy and paste from the hardware thread.
Hoping someone can help, DD1 last night, playing iRacing, done a few laps, came into the pits to change setup, and noticed my wheel was unresponsive.
Then i Noticed the pop up below, from the Fanatec Firmware Updater, my wheelbase and wheel are not recognized by any software, Fanalabs or Fanatec control panel.
Done the power on power off dance multiple times (wheelbase starts, Fanatec message on the LCD and wheel turns), reboot computer etc., can't do a firmware reload or roll back as the base is not found, was on the latest driver since release, no problems at all until this.
Anyone seen this before or possibly has a fix? I didnt initiate any update at all, like i said, i was in game at that moment.
thanks in advance,
Chris
Sign In or Register to comment.
Howdy, Stranger!
It looks like you're new here. If you want to get involved, click one of these buttons!
Sign In with Fanatec US Register
Sign In with Fanatec Australia Register
Sign In with Fanatec Japan Register
Sign In with Fanatec Europe Register
Imprint | Privacy Policy | fanatec.com
I am the owner of a CSL DD 8nm year 2021 and Formula v2.5x and I recently acquired the QR2 so as to update the connection, initially I had the 464 driver and related firmware, then reading in the various forums I downgraded the firmware with the 355 driver, I was wondering, then do I leave the 355 driver installed or can I switch to the 464 but without updating the firmware? what should be done?
Is it possible to know whether either of these versions will (finally) bring support for the Xbox SDK?
Would you even believe what ever they say?