Hey guys I have a problem here: I just deleted everything about Fanatec and downloaded again. Everything was default (settings), I set it up as I wanted and nothing happened. I mean, everything is saved in settings, but when I use my wheel in game, is like having everything in default (1080 o) Can someone give me an answer?? Thanks a lot, appreciate it!!
Depends on where you saved it and which set you are using.
For example from my CSL Elite + base (driver 356) . You see in the pic below that I have saved 5 different sets and inside the driver app set number 1 is marked. (usually if not changed is your default. Dont remember if I have changed set 1 but anyway).
While driving or before driving you can choose the set you want from your steering wheel or even tune it as you like without going into the drivers app.
in manual for your base and wheel combo (follow the link below)
I had my wheel less than a month & starting to hear squeaking from my pedals. I know in time I should grease them but should it be so quick or could it be something else?
hi, since driver 347 i don't have anymore the motor firmware version showed and the possibility to update it in the fanatec driver software, i tried to roll back to 365 and 373 from actual one(374) but no solution. can you help?
Wheel Base Model csl elite 1.1
Steering Wheel Model: podium hub
Driver Version: 374
Base FW Version: 675
Motor FW Version: 22(not showed anymore in sw and not upgradable/downgradable)
Wheel FW Version: 3
FanaLab Version: .not installed
already posted on driver section but no answer or hel from there :(
i already tried repair and driver reinstall, always same result.... 347 drivers show motor firmware 22, driver above nothing.
Just updated my CSL Elite 1.1 to the 373 drivers this morning in prep for my CSL WRC wheel coming this week. I noticed a new tuning option in the tuning menu. Can't remember exactly but I think it was BRi or something. Been searching but haven't been able to find any info on it and wanted to see if anyone here had a heads up about what it is. Thanks.
Hi guys! I would like to ask you if I must upload from 373 drivers TO 374 DRIVERS for my CSL Elite Wheel Base officially licensed for PS4! Thanks for your time, appreciate it!
Most probably you saw the BLI setting formerly known as ABS. Got renamed because the name was confusing and it had nothing to do with Telemetry based ABS.
I think V1.1 before was not supporting the tuning menu tab due to less advanced electronics as per various posts from the developers in this forum. Not sure with the new drivers though. Better check in the beta 373 thread.
Yeah mate sorry, confused post... btw seems my wheelbase is not compatible with tuning menu... curious to know if it is the only differnece for 50 euros in the wheelbases :) hehe
In the end i rolled back to 347 drivers for the motor firmware issue, seems there is no way to have it active and editable with newer driver package.
Hi guys, this post is for a friend of mine that doesn't speak english.
He recently bought this stuff:
magnetic paddle
h shifter
handbrake
clubsport pedal v3
podium hub with clubsport button module(no fanatec wheel attached, only the hub)
CSL Elite+ for PS4 wheelbase.
He upgaded driver to lastest 374 version and his firmware now are:
v.675 wheelbasefirmware
v.22 motor firmware
v.3 pdium hub firmware
if he connect the rig to pc for driver check and update everything works fine, but if he connect it to the ps4 pro nothing happens; the wheelbase and all the peripherals are not working or showed anywhere and there is no way to make it works.
He tried ps4 mode, compatibility mode, with podium hub installed on wheelbase and without it, but no solution.
Comments
Hey guys I have a problem here: I just deleted everything about Fanatec and downloaded again. Everything was default (settings), I set it up as I wanted and nothing happened. I mean, everything is saved in settings, but when I use my wheel in game, is like having everything in default (1080 o) Can someone give me an answer?? Thanks a lot, appreciate it!!
I have downloaded 64 bit 328 version Fanatec
Depends on where you saved it and which set you are using.
For example from my CSL Elite + base (driver 356) . You see in the pic below that I have saved 5 different sets and inside the driver app set number 1 is marked. (usually if not changed is your default. Dont remember if I have changed set 1 but anyway).
While driving or before driving you can choose the set you want from your steering wheel or even tune it as you like without going into the drivers app.
in manual for your base and wheel combo (follow the link below)
https://fanatec.com/media/pdf/ec/5b/68/CSL-E-F1-SET-Manual-EU-AU-EN_Web_06_MO35JLumwZ4kV8e.pdf
Chapter 6.3 in pages 34-37 it is showing you how to do it.
Thanks Alexandre I fortunately found a solution!
No worries. Glad you are up and running. 😉
From what platform you play bud?
Can anyone please inform if the: CSL Elite Steering Wheel P1 for PS4 needs an update or can install 373 driver package?
Both.... but mostly PS4 cause my pc is very old and slow. 😉
when updating one by one after the 373 each firmware you can press update the steering wheel and see if it has an update for P1.
Question
I had my wheel less than a month & starting to hear squeaking from my pedals. I know in time I should grease them but should it be so quick or could it be something else?
hi, since driver 347 i don't have anymore the motor firmware version showed and the possibility to update it in the fanatec driver software, i tried to roll back to 365 and 373 from actual one(374) but no solution. can you help?
already posted on driver section but no answer or hel from there :(
i already tried repair and driver reinstall, always same result.... 347 drivers show motor firmware 22, driver above nothing.
Just updated my CSL Elite 1.1 to the 373 drivers this morning in prep for my CSL WRC wheel coming this week. I noticed a new tuning option in the tuning menu. Can't remember exactly but I think it was BRi or something. Been searching but haven't been able to find any info on it and wanted to see if anyone here had a heads up about what it is. Thanks.
For WRC you need driver 374, you will find it here in the downloads section.
Hi guys! I would like to ask you if I must upload from 373 drivers TO 374 DRIVERS for my CSL Elite Wheel Base officially licensed for PS4! Thanks for your time, appreciate it!
Ahh crud.... Thanks for the heads up. This is why I should not have done this early in the morning...lol.
373 is the same with 374. in 374 it includes the firmware for the new WRC wheel.
Most probably you saw the BLI setting formerly known as ABS. Got renamed because the name was confusing and it had nothing to do with Telemetry based ABS.
Ok Alex thanks! You're always here for me bud🤣
If anything new comes out, are you posting it here? (I'm talking for new updates for the wheels, new drivers etc.)
Im running right now:
373 PC Drivers
674 Wheel Base Firmware
22 Wheel Base Motor Firmware
Actually all the new beta drivers are being posted in the Fanatec Software section in the Beta threads.
https://forum.fanatec.com/categories/beta-drivers
For new product releases and their software you can find them in the web-shop site under the download section.
For example the 374 is found here : https://fanatec.com/eu-en/csl-elite-steering-wheel-wrc
Glad I am able to help you buddy. 🙃
Learned a few things by reading the gurus of the forum from the development team and beta testers. ☺️
actually the tuning menu is not working in my cls elite 1.1, is it the seme for you? it tells me my wheelbase doesn't support the tuning function.
also for you the motor firmware voice disappeared?
yup the bli is the replacement for the ABS voice in the menu!
Panos is having a CSL Elite + PS4 not a V1.1
Maybe you got confused with Sterling's post.
I think V1.1 before was not supporting the tuning menu tab due to less advanced electronics as per various posts from the developers in this forum. Not sure with the new drivers though. Better check in the beta 373 thread.
Alex, appreaciate it bro, is all my updates the latest? (I mentioned them above)..
Yeah mate sorry, confused post... btw seems my wheelbase is not compatible with tuning menu... curious to know if it is the only differnece for 50 euros in the wheelbases :) hehe
In the end i rolled back to 347 drivers for the motor firmware issue, seems there is no way to have it active and editable with newer driver package.
Hi guys, this post is for a friend of mine that doesn't speak english.
He recently bought this stuff:
magnetic paddle
h shifter
handbrake
clubsport pedal v3
podium hub with clubsport button module(no fanatec wheel attached, only the hub)
CSL Elite+ for PS4 wheelbase.
He upgaded driver to lastest 374 version and his firmware now are:
v.675 wheelbasefirmware
v.22 motor firmware
v.3 pdium hub firmware
if he connect the rig to pc for driver check and update everything works fine, but if he connect it to the ps4 pro nothing happens; the wheelbase and all the peripherals are not working or showed anywhere and there is no way to make it works.
He tried ps4 mode, compatibility mode, with podium hub installed on wheelbase and without it, but no solution.
Does anybody have suggestion to make it work?
EDIT: Hristo corrected me below.
Need a coffee urgently. 😇
Podium Button Module Endurance is not compatible with CSL Elite wheel bases.
Shit. I forgot that. Need a coffee.
Thanks Hristo for correcting me. 😎
No podium advanced module, only podium hub and clubsport button module... Everything is compatible on spec description with ps4
Ok. To clear things up.
This is the Podium Button Module Endurance
And this is the Clubsport Button Cluster Pack
Which one your friend has?