Hello, I have found the profiles. Thank you very much for your work. I have adjusted everything so far and the automatic vehicle assignment works. However, I have one question. If I set everything as described (I have a DD1, so I multiply the FFB value * 1.25) then my DD1 in Fanalab runs at 9.6Nm. In iRacing, the AMG GT3 2020 is too light for me personally, I hardly have any feedback. Am I doing something wrong, or are the settings so “smooth”. I then adjusted my settings in Fanalab and now the base also runs at 20Nm and I have good feedback in iRacing. Can I do this or am I doing something wrong here? Enclosed are my screenshots.
I would be very pleased to receive your feedback. Thank you very much
The Merc 2020 profile has a FFB strength of 60 % (like basically all my profiles) which equals 15 Nm. You need to set it to 75 % (60 * 1.25) to get the same 15 Nm. I have no idea how you ended up with a Nm value of 9.6 Nm - this is not the intended FFB strength for this car at all. All the other settings from your screenshots are also totally different to the settings I have saved to the profile.
Hello, yes I had adjusted that because it was too smooth for me. I have now reset everything and re-imported the profile file from the AMG. Do I leave force feedback scale at linear (I have 11.3) or at peak (I have 15nm)?
Should i switch in iracing than to peak or linear?
Am new to fanalab and using a DD+. Ive loaded Maurice’s profiles for iRacing but just wanted to clarify how it works.
When in game, does fanalab take priority over which ever tuning menu profile my wheel base is currently set to? I read on earlier posts that it may temporarily “overwrite” tuning menu profile 1?
When you load the game and choose the car to drive in race, if Fanalab is setup correctly (Should be if your using Maurice's profiles and instructions) it will load the profile that has been attached to that car and will indeed use the saved settings and change your wheels tuning menus.
Thanks! Its all loading up as I can see fanalab showing the last car I drove. My question is should these settings be visible on my wheelbase ie profile 1 ? I currently have my GT7 settings on profile 1 on my wheelbase.
Yes it should, each game you use should have either, one profile only for all cars (Needs to be marked as the default to load) when game is loaded (No support for auto car detection), or a profile for every car that gets load as you change cars (No profiles marked as Default to load) (Supports auto car detection). Doing this ensures you will have the correct setup for each game automatically.
Hi Maurice, I see you are hard at work on the iRacing update including AMS 1.6, any eta for that? Just got my first fanatec and am waiting for this newest release to jump into Fanalab. Thanks!
Hi Maurice Böschen, I want to ask a question. when 60% x 1.25 = 75% - for DD1 is set in your profile, and then should
I set the same in the game, for example, if you have 60% written in the readme, then also x1.25 = 75% or leave it
at 60%? Thanks .. sorry for my english
Hi Diego, in your case I think YouTube and Reddit are your best friends !. After that if you still have questions or if your base is DD 1/ 2 or CS DD/+ you can come here and use Maurice profiles.
Comments
is this why fanalab keeps crashing in ams2? does removing that line fix it?
Yes, in file "ProfileCarsList_AMS2.xml" change line 104 from
<LamborghiniEssenzaSCV12 Profile="AMS2 Lamborghini Essenza SCV12.pws" CarName="Lamborghini Essenza SCV12" /> />
to
<LamborghiniEssenzaSCV12 Profile="AMS2 Lamborghini Essenza SCV12.pws" CarName="Lamborghini Essenza SCV12" />
save file and fanalab should no longer crash
btw. does the automatic profile select work for you guys?
legend thank you. it hasn't been working correctly for me but I chalked it up to the new update changing stuff. was working fine previously
Good morning,
sorry for the question, I am new to the topic “Fanalab Profiles”. I use a Podium DD1. Which profiles can I use for the Base? I am a bit confused...
Can someone please help me, thank you very much!
Daniel
Hello, I have found the profiles. Thank you very much for your work. I have adjusted everything so far and the automatic vehicle assignment works. However, I have one question. If I set everything as described (I have a DD1, so I multiply the FFB value * 1.25) then my DD1 in Fanalab runs at 9.6Nm. In iRacing, the AMG GT3 2020 is too light for me personally, I hardly have any feedback. Am I doing something wrong, or are the settings so “smooth”. I then adjusted my settings in Fanalab and now the base also runs at 20Nm and I have good feedback in iRacing. Can I do this or am I doing something wrong here? Enclosed are my screenshots.
I would be very pleased to receive your feedback. Thank you very much
You did something wrong with the FFB calculation.
The Merc 2020 profile has a FFB strength of 60 % (like basically all my profiles) which equals 15 Nm. You need to set it to 75 % (60 * 1.25) to get the same 15 Nm. I have no idea how you ended up with a Nm value of 9.6 Nm - this is not the intended FFB strength for this car at all. All the other settings from your screenshots are also totally different to the settings I have saved to the profile.
Hello, yes I had adjusted that because it was too smooth for me. I have now reset everything and re-imported the profile file from the AMG. Do I leave force feedback scale at linear (I have 11.3) or at peak (I have 15nm)?
Should i switch in iracing than to peak or linear?
This is linear
This is peak
I always save my profiles with FFS PEAK. This is completely independent from the ingame setting which has to be Linear for every DD Base.
Hello Maurice, donyou Now When the new profiles cake out for Ams2 with 1.6 update? Thank you for that
Next week once a new Lab Version is released after the game updates of iRacing, R3E and LMU.
Ah top Thanks 👍🏻😊
Hi guys,
Am new to fanalab and using a DD+. Ive loaded Maurice’s profiles for iRacing but just wanted to clarify how it works.
When in game, does fanalab take priority over which ever tuning menu profile my wheel base is currently set to? I read on earlier posts that it may temporarily “overwrite” tuning menu profile 1?
Thanks in advance
When you load the game and choose the car to drive in race, if Fanalab is setup correctly (Should be if your using Maurice's profiles and instructions) it will load the profile that has been attached to that car and will indeed use the saved settings and change your wheels tuning menus.
Thanks! Its all loading up as I can see fanalab showing the last car I drove. My question is should these settings be visible on my wheelbase ie profile 1 ? I currently have my GT7 settings on profile 1 on my wheelbase.
Hi all!
I am new to the simracing world. I bought a ready2race bundle a couple of months ago (a csl dd qr2 @8nm) and I am playing iRacing.
I am really not happy with the feel of the steering wheel and the force feedback, although I have made experiments and changes.
So I wanted to ask: are there maybe any ready, available profiles for the csl dd and iRacing, in order to give them a try?
Thanks a lot in advance for any input.
Yes it should, each game you use should have either, one profile only for all cars (Needs to be marked as the default to load) when game is loaded (No support for auto car detection), or a profile for every car that gets load as you change cars (No profiles marked as Default to load) (Supports auto car detection). Doing this ensures you will have the correct setup for each game automatically.
The new LMU-Update is so good... hopefully Maurice cooks some Profiles for the new LMGT3 cars :)
Hi Maurice, I see you are hard at work on the iRacing update including AMS 1.6, any eta for that? Just got my first fanatec and am waiting for this newest release to jump into Fanalab. Thanks!
Hoping we can get a M2 profile from Maurice soon - cheers
I recommend to try BMW M4 GT4 profile for m2. Works very good in my opinion.
Anyone have a profile for the iRacing Ferrari 499P?
hey guys i cant find the profiles for the clubsport DD+ anywhere can somebody help me? thankyou
Cheers bud will give that a shot
Hello guys,
I just started playing LMU LMGT3 with my CSL DD 8nm on my computer.
I can't feel the car well so I wondered if you can help me.
Do you have good setup profile in fanatec control panel or in fanalab for my CSL DD 8nm ??
Thanks in advance and sorry for bad english ^^
Does anyone have a good profile for the Acura NSX GT3 EVO 22 for iR?
Thanks.
Hi Maurice,
Can these profiles be used with CSL DD 8nm?
Thanks
Hi guys, is there a thread with instructions for a quick start guide? This is my first Fanatec and also PC, so everything is new to me. Thanks!
Hi Diego, in your case I think YouTube and Reddit are your best friends !. After that if you still have questions or if your base is DD 1/ 2 or CS DD/+ you can come here and use Maurice profiles.